Sprays of Rays Logo
   By American Turbine Inc. • 1-800-328-4827 Ext. 5981 New toll free: 1-877-748-4857
Home Button
About Us Button
Components Button
DHA and Tanning Button
Owner's Manual Button
Equipment Maintenance Button
What is HVLP and LVLP Button
Sound Levels Button
Warranty Button
Shipping Information Button
Payment Information Button
Contact Us Button
American Turbine Inc. HVLP Paint Spray Systems
abTan Button
Find A Distributor Button
Our Favorite Links Button

Equipment Maintenance

Daily Maintenance

The Last Client has Gone Home for the Day - Time to Clean Up

It is recommended that any solutions in the cups be emptied back into their original containers. The extra cups should be washed out with lukewarm water and a drop of dish soap, rinsed, inverted and left to dry overnight. For cleaning of the gun, fill one of the 6 oz. cups with 2-3 ounces of lukewarm water and a drop of dish soap. Spray the soapy water through the gun into a sink. Then fill the cup with clear water and spray until the water runs clear. Remove the cup, the excess water will flow out of the tube, and spray air only for 30 seconds. Wipe the gun down, as well as the hose and machine.

On-going maintenance

It is recommended that you use the gun cleaning kit once every two-four weeks to ensure your gun's peak performance. Check your air pre-filter every week. It can be cleaned with any mild soap and water, dried and reinstalled. Replace pre-filter as necessary. To order new pre-filters, give us a call at 800-328-4827 Ext. 5981.

Gun Cleaning Kit

Cleaning the gun with the gun cleaning kit included with your system:

Included in this kit: cleaning brush, nozzle removal tool, packing adjustment wrench.

We assume that you have done your daily maintenance by running the soapy water and clear water through the gun.

  1. Remove pattern control ring (black ring on the front of the gun) by unscrewing it counterclockwise, remove detent plate and detent spring and clean in soapy water, rinse.
  2. Remove material control knob at the back of the gun. This is the larger black knob that butts up to the silver part of the gun. Unscrew that counterclockwise. Pull back on the trigger and pull the needle out through the back of the gun.
  3. Remove the nozzle with the nozzle removal tool. The tool will fit tightly around the nozzle. Turn it counterclockwise. If it is hard for you to turn, lay the gun on the side of a table flat side down, holding the tool over the nozzle and tap with a hammer to loosen the nozzle enough for you to unscrew by hand. Clean nozzle with soapy water, rinse.
  4. Run the brush through the body of the gun as necessary, front to back.
  5. It should not be necessary to clean the clear tubes running up from the cup if you have been running soapy water and clear water through the gun on a daily basis.
  6. Attach the turbine air hose to the gun and blow air through to dry out the body.
  7. Apply a thin coat of Vaseline to the shaft of the needle, threads of the material control body and adjustment screw, and the threads of pattern control ring.
  8. Reassemble gun.
Gun with notes

If you have any problems while cleaning your gun, please give us a call and we can walk you through the process.

1-800-328-4827 Ext. 5981 or 1-877-748-4857

Warranty

The Sprays of Rays system is covered from mechanical and electrical defects for 48 months from date of purchase/registration (see registration form included with your machine).

What is not covered under this warranty

This warranty will not cover damage resulting from misuse of the product, negligence, use of improper voltage, alterations made to the equipment or service done by someone other than American Turbine. The warranty does not cover consumables such as filters.

The Sprays of Rays equipment is intended solely for spraying tanning and exfoliating solutions and should not be used to spray any flammable or volatile solutions.

Should you have any problems with the equipment, please call us at 1-800-328-4827
Ext. 5981 or
1-877-748-4857 immediately and our technical staff will assist you.
Back to Top

Shipping

Shipping Information - Continental United States

All shipments are via UPS ground from North St. Paul, Minnesota, 55109.

Sprays of Rays Units - $20.00 insurance included

Orders for accessories will be actual shipping costs based on zip code.

Shipping Information - Hawaii, Alaska, Canada and Puerto Rico

Actual shipping costs via UPS ground based on zip code/postal code.

Please call for an estimate at 1-800-328-4827 Ext. 5981 or 1-877-748-4857,
or email us at
Spraysofrays@yahoo.com
Back to Top

Payment Information

Payment accepted via Paypal, Visa, Mastercard, Discovery, and American Express; money orders, cashier's check and personal checks (must clear).

Please call us at 1-800-328-4827 Ext. 5981 or 1-877-748-4857 if you would prefer to place an order by phone rather than through Paypal.

Shipments within Minnesota - 6.5% sales tax applies.

We accept the following credit cards through Paypal:

Back to Top

 

Find a Distributor

Our Authorized Distributors

Jamaica Me Tan
866-845-0811

Simply Sunless
936-649-1325
Kimberlee Hussey

Back to Top

 

Contact Us

American Turbine Inc.
2517 E. 7th Avenue
P. O. Box 9115
North St. Paul, MN 55109
651-748-8030
Fax: 651-748-0028
Toll Free: 1-800-328-4827 Ext. 5981 or

1-877-748-4857

Hours of Operation:

8:00 a.m. - 5:00 p.m. CST M-F
Back to Top

Discover